IoT Device with built in WiFi Hotspot, WiFi or FAST Ethernet
Output Power 4 x 60 WRMS @ 4Ohm, 8Ohm, 70V, 100V (30W at 2Ohm)
AUDIO SPECS
Inputs
Analog: 4 Balanced analog Inputs with user selectable 26dB, 34dB, and mic level input sensitivity
4 Unbalanced RCA inputs with user selectable 26dB and 34dB input sensitivity
***Note – Unbalanced and RCA inputs share the same analog input channel
Dante: 4 x 4 Dante at 48kHz, Multicast, or Unicast
AES 67: Configurable via the Dante Controller Software
THD+N 0.1% (20Hz to 20kHz)
Frequency Response +/- 0.5 dB @ 4Ohm, 8Ohm, 70V, 100V, -2.5dB @ 20kHz at 2Ohm
Signal to Noise Level 102dB (20Hz to 20kHz referenced to 8Ohm)
Crosstalk 70dB (20Hz to 20kHz)
I/O Latency 1 ms DSP latency under any condition
Load Impedance LowZ down to 2 ohms, 70V direct, and 100V Direct per channel
Output Classification Class D with Proprietary Smart Power Bridge Technology allowing bridged output functionality without sacrificing an amplifier channel
DC Offset +/- 3mV
DSP
DSP Architecture Analog Devices Sigma 96kHz DSP Processor with 32-bit Core with Sample Rate Converters
Input Matrix Routable matrix; any input to any output with primary and secondary input priority
Crossovers Up to 48 dB/Octave IIR Filters (Linkwitz Riley and Butterworth) and Bessel
Parametric EQ 8 Band Parametric EQ per channel
Output Delay 100ms per channel
Output Protection DC, VHF, and AC Mains Protection, Over-temp and Current Limiter, fan fault detection
Limiting Peak Voltage and RMS Voltage
Load Monitoring Realtime Load Monitoring and Pilot Tone Detection from Internal or External Sources
CONTROL, MONITORING, NETWORK
Network Connectivity Wi-Fi or 100MB Ethernet with PoE or Built in Wi-Fi Access Point (IEEE 802.11 b/g/n WPA, WPA2, WEP)
User Interface Web Browser User Interface, 3rd Party API control, Cloud Control, or SharkWare
Operating Systems MAC, iOS, PC, Android
Event Reporting User Downloadable and Viewable Event and Fault log - POE allows for enhanced error monitoring
External I/O
External I/O In: Toggles Remote On/Off | External I/O Out: Indicates Amplifier Health
4 general purpose Input and Output pins for general input
Triggering and output statuses: Coming soon
Cloud IoT AWS Cloud based IoT functionality
OPS DATA
AC Mains 100VAC - 240VAC +/- 15% 50Hz or 60Hz
Temperature Storage: -20°C to 90° C - Operating: 0°C to 60° C
Power Supply Universal Switch Mode Power Supply
Safety Approvals UL, CSA, CE, ETL, FCC, CCC, KETI, NOM, ROHS, PSE
PHYSICAL SPECS
Dimensions (L x W x H)
Product: 11.82” x 8.58” x 1.71” (300.11mm x 278mm x 43.5mm)
Shipping: 18” x 11” x 2.75” (457.2mm x 300mm x 69.85mm)
Weight 7lbs / 3.1kg | Shipping: Coming Soon
Cooling Front to Rear Variable Fan Speed Cooling | Fan Noise at idle is 50dB @ 1m | Fan Noise at 50% is 57dB @1m | Fan Noise at full speed is 63dB @1m
Connectors Analog Input: 3 pin Amphenol Anytek, Output: 2 pin Amphenol Anytek, External IO: 8 pin Amphenol Anytek, Power in: IEC, Ethernet RJ45 In for Dante, and RCA input
AUDIO SPECS
Inputs
Analog: 4 Balanced analog Inputs with user selectable 26dB, 34dB, and mic level input sensitivity
4 Unbalanced RCA inputs with user selectable 26dB and 34dB input sensitivity
***Note – Unbalanced and RCA inputs share the same analog input channel
Dante: 4 x 4 Dante at 48kHz, Multicast, or Unicast
AES 67: Configurable via the Dante Controller Software
THD+N 0.1% (20Hz to 20kHz)
Frequency Response +/- 0.5 dB @ 4Ohm, 8Ohm, 70V, 100V, -2.5dB @ 20kHz at 2Ohm
Signal to Noise Level 102dB (20Hz to 20kHz referenced to 8Ohm)
Crosstalk 70dB (20Hz to 20kHz)
I/O Latency 1 ms DSP latency under any condition
Load Impedance LowZ down to 2 ohms, 70V direct, and 100V Direct per channel
Output Classification Class D with Proprietary Smart Power Bridge Technology allowing bridged output functionality without sacrificing an amplifier channel
DC Offset +/- 3mV
DSP
DSP Architecture Analog Devices Sigma 96kHz DSP Processor with 32-bit Core with Sample Rate Converters
Input Matrix Routable matrix; any input to any output with primary and secondary input priority
Crossovers Up to 48 dB/Octave IIR Filters (Linkwitz Riley and Butterworth) and Bessel
Parametric EQ 8 Band Parametric EQ per channel
Output Delay 100ms per channel
Output Protection DC, VHF, and AC Mains Protection, Over-temp and Current Limiter, fan fault detection
Limiting Peak Voltage and RMS Voltage
Load Monitoring Realtime Load Monitoring and Pilot Tone Detection from Internal or External Sources
CONTROL, MONITORING, NETWORK
Network Connectivity Wi-Fi or 100MB Ethernet with PoE or Built in Wi-Fi Access Point (IEEE 802.11 b/g/n WPA, WPA2, WEP)
User Interface Web Browser User Interface, 3rd Party API control, Cloud Control, or SharkWare
Operating Systems MAC, iOS, PC, Android
Event Reporting User Downloadable and Viewable Event and Fault log - POE allows for enhanced error monitoring
External I/O
External I/O In: Toggles Remote On/Off | External I/O Out: Indicates Amplifier Health
4 general purpose Input and Output pins for general input
Triggering and output statuses: Coming soon
Cloud IoT AWS Cloud based IoT functionality
OPS DATA
AC Mains 100VAC - 240VAC +/- 15% 50Hz or 60Hz
Temperature Storage: -20°C to 90° C - Operating: 0°C to 60° C
Power Supply Universal Switch Mode Power Supply
Safety Approvals UL, CSA, CE, ETL, FCC, CCC, KETI, NOM, ROHS, PSE
PHYSICAL SPECS
Dimensions (L x W x H)
Product: 11.82” x 8.58” x 1.71” (300.11mm x 278mm x 43.5mm)
Shipping: 18” x 11” x 2.75” (457.2mm x 300mm x 69.85mm)
Weight 7lbs / 3.1kg | Shipping: Coming Soon
Cooling Front to Rear Variable Fan Speed Cooling | Fan Noise at idle is 50dB @ 1m | Fan Noise at 50% is 57dB @1m | Fan Noise at full speed is 63dB @1m
Connectors Analog Input: 3 pin Amphenol Anytek, Output: 2 pin Amphenol Anytek, External IO: 8 pin Amphenol Anytek, Power in: IEC, Ethernet RJ45 In for Dante, and RCA input
LEA Power Amp 4 Channel x 60 watt @ 4Ohm, 8Ohm, 70V and 100V
- Product Code:CS64D
- U.O.M: ea
- Available: 0 (On backorder)
-
$2,426.09 GST Excl.$2,790.00 GST Inc.