4 Channel x 700 watt @ 4 ohm , 8 ohm, and 100V per channel
4 Channel x 700 watt @ 4 ohm , 8 ohm, 70V and 100V per channel. Internal DSP w Crossovers, loT Device with built in WiFi Hotspot, WiFi or FAST Ethernet connectivity and Highly Efficient Power Supply with Class D Output Stage
Web Browser based UI – works on any device with no software to download
Direct LoZ and HiZ (70V or 100V) selectable per channel
Proprietary Smart Power Bridge allows user to bridge a channel to achieve double the power of that channel without sacrificing an amplifier channel
3 Ways to Connect 1.) Built in WiFi Access Point 2.) Connects to existing WiFi network 3.) Local Area Network Ethernet connection
96kHz Analog Devices DSP with Input Routing, multiple 48dB/Oct crossover filters, 8 Parametric EQ filters, user configurable speaker limiters, and real time load monitoring
Universal Switch Mode Power Supply with PFC. Operation from 100VAC – 240VAC +/-15%
Analog fully routable inputs
External I/O Port for Remote On/Off and fault monitoring
Highly Efficient Class D Output Stage for low AC Current draw
SPECIFICATIONS
Audio Spec
Inputs Analog: Balanced Inputs with user selectable 26 dB and 34 dB input sensitivity (2CH = 2 inputs, 4CH = 4 inputs, 8CH = 8 inputs)
Dante: 8 x 8 Dante at 96kHz or 48kHz, Multicast or Unicast
AES 67: Configurable via the Dante Controller Software
THD+N 0.1% (20Hz to 20kHz)
Frequency Response +/- 0.5 dB @ 4Ohm, 8Ohm, 70V, 100V, -2.5dB @ 20kHz at 2Ohm
Signal to Noise Level 105dB (20Hz to 20kHz referenced to 8Ohm)
Crosstalk 70dB (20Hz to 20kHz)
I/O Latency 1 ms DSP latency under any condition
Load Impedance LowZ down to 2 ohms, 70V direct, and 100V Direct per channel
Amplifier Output Classification Class D with Proprietary Smart Power Bridge Technology allowing bridged output functionality without sacrificing an amplifier channel
DSP
DSP Architecture Analog Devices Sigma 96kHz DSP Processor with 32-bit Core with Sample Rate Converters
Input Matrix Routable matrix; any input to any output with primary and secondary input priority
Crossovers Up to 48 dB/Octave IIR Filters (Linkwitz Riley and Butterworth)
Parametric EQ 8 Band Parametric EQ per channel
Output Delay 100ms per channel
Output Protection DC, VHF, and AC Mains Protection, Overtemp and Current Limiter, fan fault detection
User Adjustable Limiting Peak Voltage and RMS Voltage
Load Monitoring Realtime Load Monitoring and Pilot Tone Detection from Internal or External Sources
Control, Monitoring, Network
Network Connectivity WiFi or 100MB Ethernet with PoE or Built in WiFi Access Point (IEEE 802.11 b/g/n WPA, WAP2, WEP)
User Interface Web Browser User Interface or 3rd Party API control (Q-Sys coming soon)
Supported Operating Systems MAC, iOS, PC, Android
Event Reporting User Downloadable and Viewable Event and Fault log - POE allows for enhanced error monitoring
External I/O External I/O In: Toggles Remote On/Off
External I/O Out: Indicates Amplifier Health
Cloud IoT Cloud based IoT functionality
Operation
AC Mains 100VAC - 240VAC +/- 15% 50Hz or 60Hz
Temperature Storage: -20°C to 90° C - Operating: 0°C to 60° C Power Supply
Universal Switch Mode Power Supply with Power Factor Correction (No PFC in 84D, 164D, 88D, & 168D)
Safety Approvals UL, CSA,CE, ETL, FCC, CCC, KETI, NOM , ROHS, PSE
Physical Spec
Dimensions (L x W x H) 362mm x 482mm x 1U Shipping: 508mm x 578mm x 95.25mm
Weight Product 15.5 lbs / 7kg Shipping Weight 9.1 kg
Cooling Front to Rear Variable Fan Speed Cooling Fan Noise at idle is 50dB @ 1m Fan Noise at 50% is 57dB @1m Fan Noise at full speed is 63dB @1m
Connectors Analog Input: 3 pin Amphenol Anytek, Output: 2 pin Amphenol Anytek, External IO: 3 pin Amphenol Anytek, Power in: IEC, Ethernet RJ45 In for Control, Primary and Secondary RJ45 in for Dante *Note*: 84D, 164D, 88D, & 168D do not have potentiometers on the rear panel
Web Browser based UI – works on any device with no software to download
Direct LoZ and HiZ (70V or 100V) selectable per channel
Proprietary Smart Power Bridge allows user to bridge a channel to achieve double the power of that channel without sacrificing an amplifier channel
3 Ways to Connect 1.) Built in WiFi Access Point 2.) Connects to existing WiFi network 3.) Local Area Network Ethernet connection
96kHz Analog Devices DSP with Input Routing, multiple 48dB/Oct crossover filters, 8 Parametric EQ filters, user configurable speaker limiters, and real time load monitoring
Universal Switch Mode Power Supply with PFC. Operation from 100VAC – 240VAC +/-15%
Analog fully routable inputs
External I/O Port for Remote On/Off and fault monitoring
Highly Efficient Class D Output Stage for low AC Current draw
SPECIFICATIONS
Audio Spec
Inputs Analog: Balanced Inputs with user selectable 26 dB and 34 dB input sensitivity (2CH = 2 inputs, 4CH = 4 inputs, 8CH = 8 inputs)
Dante: 8 x 8 Dante at 96kHz or 48kHz, Multicast or Unicast
AES 67: Configurable via the Dante Controller Software
THD+N 0.1% (20Hz to 20kHz)
Frequency Response +/- 0.5 dB @ 4Ohm, 8Ohm, 70V, 100V, -2.5dB @ 20kHz at 2Ohm
Signal to Noise Level 105dB (20Hz to 20kHz referenced to 8Ohm)
Crosstalk 70dB (20Hz to 20kHz)
I/O Latency 1 ms DSP latency under any condition
Load Impedance LowZ down to 2 ohms, 70V direct, and 100V Direct per channel
Amplifier Output Classification Class D with Proprietary Smart Power Bridge Technology allowing bridged output functionality without sacrificing an amplifier channel
DSP
DSP Architecture Analog Devices Sigma 96kHz DSP Processor with 32-bit Core with Sample Rate Converters
Input Matrix Routable matrix; any input to any output with primary and secondary input priority
Crossovers Up to 48 dB/Octave IIR Filters (Linkwitz Riley and Butterworth)
Parametric EQ 8 Band Parametric EQ per channel
Output Delay 100ms per channel
Output Protection DC, VHF, and AC Mains Protection, Overtemp and Current Limiter, fan fault detection
User Adjustable Limiting Peak Voltage and RMS Voltage
Load Monitoring Realtime Load Monitoring and Pilot Tone Detection from Internal or External Sources
Control, Monitoring, Network
Network Connectivity WiFi or 100MB Ethernet with PoE or Built in WiFi Access Point (IEEE 802.11 b/g/n WPA, WAP2, WEP)
User Interface Web Browser User Interface or 3rd Party API control (Q-Sys coming soon)
Supported Operating Systems MAC, iOS, PC, Android
Event Reporting User Downloadable and Viewable Event and Fault log - POE allows for enhanced error monitoring
External I/O External I/O In: Toggles Remote On/Off
External I/O Out: Indicates Amplifier Health
Cloud IoT Cloud based IoT functionality
Operation
AC Mains 100VAC - 240VAC +/- 15% 50Hz or 60Hz
Temperature Storage: -20°C to 90° C - Operating: 0°C to 60° C Power Supply
Universal Switch Mode Power Supply with Power Factor Correction (No PFC in 84D, 164D, 88D, & 168D)
Safety Approvals UL, CSA,CE, ETL, FCC, CCC, KETI, NOM , ROHS, PSE
Physical Spec
Dimensions (L x W x H) 362mm x 482mm x 1U Shipping: 508mm x 578mm x 95.25mm
Weight Product 15.5 lbs / 7kg Shipping Weight 9.1 kg
Cooling Front to Rear Variable Fan Speed Cooling Fan Noise at idle is 50dB @ 1m Fan Noise at 50% is 57dB @1m Fan Noise at full speed is 63dB @1m
Connectors Analog Input: 3 pin Amphenol Anytek, Output: 2 pin Amphenol Anytek, External IO: 3 pin Amphenol Anytek, Power in: IEC, Ethernet RJ45 In for Control, Primary and Secondary RJ45 in for Dante *Note*: 84D, 164D, 88D, & 168D do not have potentiometers on the rear panel
LEA Power Amp 4 x 700 Watt DANTE DSP
- Product Code:CS704D
- U.O.M: ea
- Available: 2
-
$6,242.99 GST Excl.$7,179.44 GST Inc.$6,600.00 GST Excl.$7,590.00 GST Inc.